Mostrar mensagens com a etiqueta Motor. Mostrar todas as mensagens
Mostrar mensagens com a etiqueta Motor. Mostrar todas as mensagens

segunda-feira, 9 de fevereiro de 2015

Home built quadcopter - Maiden flight

After receiving last missing parts, namely: propellers, battery and flight controller, I had the minimum required parts to have a working prototype.
Another useful addition was a power distribution board, which is crucial to minimize cable mess and organize power lines and provide a single connector to battery. This is specially relevant when motor power draw can reach 60Amps of peak current.
I also bought a propeller balancer, which helps in having well balanced propellers that will help avoid most vibration from the frame.
Balancing a propeller is a simple procedure that resumes to adding duck tape to the lighter side of a propeller, depending on the quantity of tape and position where you add it, you can balance a propeller by simple trial an error, until you instinctively know where and how much tape to add.

During setup, special care must be taken to correctly wire components to the control board, whatever it may be (motor ESCs or radio receiver lines), to prevent swapped connections. We don't want the controller to "think" that it's controlling the forward right motor ESC, when in fact we connect the backward left motor ESC to it, or that it is receiving yaw input, but instead we connect pitch input to it.
Any mismatch and it can be disastrous, specially if we reverse power lines (+ and -), because that will surely fry some component or your entire board almost immediately.
All motors must also be tested for correct spinning direction. If spinning is incorrect, just swap two of the three cables connecting the ESC to the motor, this will reverse the spinning direction. There is also a setting in most ESCs configuration, but it's better, faster and safer to just swap cables.
After setting it all up, I locked the frame to a table, so that it would not fly, even if it wanted to, so that I could try all the motors and direction controls and assert that everything was working as supposed.
Once everything checked out ok, I went outside for my first test flight, the maiden flight. After a few centimeters of lift, it was obvious that there was something out of balance, because the quad kept on moving side-ways when it was supposed to be still. I checked the radio to see if any trimming was being applied, but that was on center, X and Z.
From further inspection it appeared to be some difference where the ESCs are attached to the arms, but it can also be related with the feedback loop constants that came pre-defined with the board, that I have not checked yet.

Did some more test flights in a more controlled environment, with an even level ground (a tennis court).
However, to my surprise, I managed to flip over the quad while it was trying to lift off. After inspection, I noticed that two motor power connections where disconnected, which was probably the cause of the flip over. I also noticed that although the 60Amps connectors that I bought looked great, they were not holding a good connection, and from further inspection I discovered this was happening because there was too much plastic (length wise) in the female connectors, that was preventing connector metal parts to mate and lock correctly.
For a quick solution, I removed all female connectors plastic covers so that this will not happen again. Later I can cut them to size, and prevent metal exposure by using plastic covers for both connectors.

After checking all motor connections again, the quad refused to power on, like if the controller was completely dead. After a few minutes I was starting to convince myself that I had fried the controller. But then I noticed that every time I connected power to the board, a light column of "magic smoke" emerged from the board. After a couple of tries, I managed to identify the SMD component that was leaking "magic smoke". And it was a simple power diode.

Partially disconnected motors (only one cable, + or -) besides flipping the quad, also have the side effect of running too much current through the ground rail, which eventually toasted the small SMD power diode.
I replaced the SMD diode with a more beefy power diode, and the board came back to life.
Once I got the board working, I re-checked every electric connection, to guarantee nothing else was loose or disconnected. I even added a few rubber bands to prevent ESC power connections to disconnect during flight.

Everything checked and ready to go, so I went for another test flight outside. A few seconds later and about 50cm high from the ground, the quad just dove to the ground, and one of the motors decided to fly solo :)
Could not believe my eyes, what was going on ?
Later I realized that on previous flip over crash and some other ruff landings from previous tests, I had cracked one motor support, without noticing it. In this last flight, the cracked support just gave in to the operational stress and finally snapped out, letting the motor loose and propeller almost cut its own motor power cables when it snapped.

Lessons to be learned ?
Check, double check and triple check everything, not just electric or electronic components and connections, but also all mechanical and moving parts, including wiggling cables that can become trapped on moving parts (propellers are killers).

sexta-feira, 23 de março de 2012

Finally, Z Axel is complete !!!

The axel screw extra length has been cut off to correct size, and motor protection and cable support have been securely reattached.
It already passed, several function tests, but the ultimate test is to cut some stock material to see if the original problem is gone, with all the load on the axel, including spindle and vacuum setup.

segunda-feira, 12 de março de 2012

Refactored Motor Support

Since the new axel mount position only has an offset distance of about 12.0mm from original axis mount position, I opted to reuse/refactor the original aluminium motor support plaque, by re-drilling new mount and pass through holes. I also had to make a circular cavity, 3.0mm deep and 34.4 mm in diameter, in order to fit the motor in a secure configuration, that it also had originaly. The picture shows motor housing on top, attached to aluminium support plaque. And below we have a flexible coupling linking the motor shaft to the ball screw axel, just above the axel support bearing which is attached to aluminium L shapped support. Now I have to find a viable solution to fix the motor metal protection, that also as a handle, to drag the motor cables back and forth.

quinta-feira, 26 de janeiro de 2012

Motor Winding PCB

After some more Design and CAD work, here is the latest version of the H3 Robot wheel, including PCB board, used to route the poles wiring. There will be a PCB on each side, i.e. one for each stepper motor phase. Each PCB will be used to wire a single phase, supplying solder points for both windings, clockwise and anti-clockwise. The PCB was designed in such a way that allows to make several cuts on the circuit, in order to make parallel phase windings, which will be useful if wire resistance is too high, or if current is too low.

domingo, 22 de janeiro de 2012

Robot wheel assembly

Due to a few requests about how the robot motor was actually being built, and how it relates to previous posted images of tires and wheels I'm building, I present here two renders of the motor assembly, to contextualize the latest H3 Robot wheels pictures.

The first render shows an alpha version of the assembly, with some zoom to be able to easily distinguish tire, wheel, magnets and the motor stator.

The second render, shows a beta version of the assembly, with some more detail on the stator. However, both of these assemblies are already outdated, since I had to make some adjustments due to an unexpect surprise I had with the tires I bought.

Tire description mentioned that it had a steel ring, which I assumed was visible and accesible and would be the tire wheel base, but unfortunatly this was not the case, since the inner steel ring is there only to provide tight fixing, when the tire is inserted, i.e. pressed onto a wheel hub.

This meant that expected tire measurements didn't include a wheel base, and since I had based my entire assembly design on this assumption, the entire assembly design had to be remade, in order to include a wheel hub.

segunda-feira, 12 de dezembro de 2011

H3 Robot In Hub Motor Rotor

H3 Robot traction will be provided by a specially built stepper motor, that will be manufactured to be completely contained within the wheel hub.
The tire will be press fitted into the wheel hub, which forms the basis of the motor rotor.
Now this may seem odd, since the rotor usually is in the center of the motor, but in this case it will be on the outside of the motor stator.
This seems reversed because motor functions, in an in hub motor, are kind of reversed, since it's not an axel that revolves, but instead it's the wheel that revolves around a static axel. In other words, the axel is fixed, it does not rotate.

To accomplish this, the wheel hub must function as the host of the stepper motor rotor, which means that the hub must have a bunch of magnets securely attached to it. Once again, this is so, because the motor works in a reversed logic to a typical motor. In other words, it's the rotor that gets the magnets instead of the stator, which is the reverse of a typical electric motor.

By definition, the rotor is the part of the motor that rotates, and the stator is the part that remains static or fixed, i.e. it does not rotate.